Guitar Repairs Winnetka CA

If you want to get that clean, jangly Vox tone, but without altering the reverb channel of your amp, you can The tone you seek can be obtained very easily by simply replacing a short wire with a capacitor and changing the value of a capacitor on the component board. If you want to know more about this method, read on for more details.

California State University - Northridge
(818) 677-3700
Northridge CA
Northridge, CA

Data Provided by:
University of Los Angeles - UCLA
(310) 825-4761
Los Angeles CA
Los Angeles, CA

Data Provided by:
California Institute of the Arts
661-255-1050 ext 7841
Valencia CA
Valencia, CA

Data Provided by:
Musicians Institute
6752 Hollywood Boulevard
Hollywood, CA
 
California ASTA Summer Institute of Music
2119 Glencoe Ave.
Venice, CA
 
California State University - Northridge
18111 Nordhoff St.
Northridge, CA
 
University of Los Angeles - UCLA
2539 Schoenberg Music Building Box 951616
Los Angeles, CA
 
California Institute of the Arts
24700 McBean Pkwy
Valencia, CA
 
California ASTA Summer Institute of Music
(310) 391-9787
Venice CA
Venice, CA

Data Provided by:
California Lutheran University
60 West Olsen Road
Thousand Oaks, CA
 
Data Provided by:

The Jangle-izer

IS THERE A WAY TO GET MORE JANGLE FROM THE NORMAL channel of my FenderPro Reverb amp? I have a 12-string Rickenbacker and would like to get that clean, jangly Vox tone, but without altering the reverb channel of my amp. —Anonymous

The tone you seek can be obtained very easily by simply replacing a short wire with a capacitor and changing the value of a capacitor on the component board. This modification will work with almost any two channel Fender amp (Twin, Super, Pro, Bandmaster, Showman, etc), and it is easily reversible should you want the stock wiring again.

This mod requires only two parts: a .01uf/400-volt capacitor and a 5uf/25-volt electrolytic capacitor. You’ll need a soldering iron and solder too, of course.

Unplug the amp and put the standby switch in the “play” mode to drain any stored electricity from the amp. Remove the four chassis screws on the top of the amp; remove the upper back panel and the cabinet strain relief on the AC cord. Unplug the speaker and remove the chassis from the cabinet. With the back of the amp facing you and looking into the chassis at the right side, you should be able to match up the components in the amp with the layout in Diagram 1. Make sure your amp is similar to the drawing before proceeding.

Notice there is a straight wire connecting the middle of the volume pot to the bright switch. You are going to replace this wire with the .01uf capacitor. Next, locate the 25uf capacitor that is going to pin 3 of the first preamp tube. You are going to replace this capacitor with the 5uf capacitor. Pay attention to the polarity of this cap. The plus (+) lead should face pin 3 of the first preamp tube, and the minus (–) lead should face the front of the amp. Double-check your work, by comparing it to Diagram 2. This is what the amp should look like now.

Put the old capacitor and the removed wire in a baggie and stash it in the bottom of the amp in case you want to put it back to stock wiring later. Reinstall the chassis, the AC cable strain relief, and the upper back panel. Plug in the speaker and you are ready to test it (make sure the speaker is plugged into the main speaker jack and not the external speaker jack). Turn on the amp, plug in your 12-string Rickenbacker, and get your Byrds on! —Gerald Weber, Kendrick Amplifiers

Click here to read the rest of the article from Guitar Player

Local Events

Rock Boy Fresh
Dates: 12/7/2020 – 12/7/2020
Location:
Key Club Nightclub Los Angeles
View Details
 

Guitar Player is a trademark of New Bay Media, LLC. All material published on www.guitarplayer.com is copyrighted @2009 by New Bay Media, LLC. All rights reserved