Guitar Repairs Palm Harbor FL

If you want to get that clean, jangly Vox tone, but without altering the reverb channel of your amp, you can The tone you seek can be obtained very easily by simply replacing a short wire with a capacitor and changing the value of a capacitor on the component board. If you want to know more about this method, read on for more details.

University of Tampa (University of Tampa - Department of Music)
(813) 253-3333
401 W. Kennedy Blvd.
Tampa, FL
 
Glenn Meyer Drum Studio
(727) 786-5646
10 Lakeview Ct
Palm Harbor, FL
Hours
1P.M.-8:30P.M.

Data Provided by:
University of Miami
(305) 284-2241
Coral Gables FL
Coral Gables, FL

Data Provided by:
Lynn University
(561) 237-7900
Boca Raton FL
Boca Raton, FL

Data Provided by:
New World School of Arts
300 NE 2nd Ave.
Miami, FL
 
University of South Florida (University of South Florida School of Music)
(813) 974-2311
4202 E. Fowler Avenue FAH 110
Tampa, FL
 
Charity's Piano Studio
(813) 388-0502
9209 Dalwood Court
Tampa, FL
Hours
Monday, Tuesday, Thursday, Friday 6 PM - 9 PM, Saturday 9 AM - 9 PM

Data Provided by:
Florida College
119 N. Glen Arven Avenue
Temple Terrace, FL
 
PianoRAMA, LLC.
Deltona, FL
 
Pleasant Hill Piano Studio
Located in Sunrise Plaza
Sarasota, FL
 
Data Provided by:

The Jangle-izer

IS THERE A WAY TO GET MORE JANGLE FROM THE NORMAL channel of my FenderPro Reverb amp? I have a 12-string Rickenbacker and would like to get that clean, jangly Vox tone, but without altering the reverb channel of my amp. —Anonymous

The tone you seek can be obtained very easily by simply replacing a short wire with a capacitor and changing the value of a capacitor on the component board. This modification will work with almost any two channel Fender amp (Twin, Super, Pro, Bandmaster, Showman, etc), and it is easily reversible should you want the stock wiring again.

This mod requires only two parts: a .01uf/400-volt capacitor and a 5uf/25-volt electrolytic capacitor. You’ll need a soldering iron and solder too, of course.

Unplug the amp and put the standby switch in the “play” mode to drain any stored electricity from the amp. Remove the four chassis screws on the top of the amp; remove the upper back panel and the cabinet strain relief on the AC cord. Unplug the speaker and remove the chassis from the cabinet. With the back of the amp facing you and looking into the chassis at the right side, you should be able to match up the components in the amp with the layout in Diagram 1. Make sure your amp is similar to the drawing before proceeding.

Notice there is a straight wire connecting the middle of the volume pot to the bright switch. You are going to replace this wire with the .01uf capacitor. Next, locate the 25uf capacitor that is going to pin 3 of the first preamp tube. You are going to replace this capacitor with the 5uf capacitor. Pay attention to the polarity of this cap. The plus (+) lead should face pin 3 of the first preamp tube, and the minus (–) lead should face the front of the amp. Double-check your work, by comparing it to Diagram 2. This is what the amp should look like now.

Put the old capacitor and the removed wire in a baggie and stash it in the bottom of the amp in case you want to put it back to stock wiring later. Reinstall the chassis, the AC cable strain relief, and the upper back panel. Plug in the speaker and you are ready to test it (make sure the speaker is plugged into the main speaker jack and not the external speaker jack). Turn on the amp, plug in your 12-string Rickenbacker, and get your Byrds on! —Gerald Weber, Kendrick Amplifiers

Click here to read the rest of the article from Guitar Player


Guitar Player is a trademark of New Bay Media, LLC. All material published on www.guitarplayer.com is copyrighted @2009 by New Bay Media, LLC. All rights reserved