Guitar Repairs Columbus NE

If you want to get that clean, jangly Vox tone, but without altering the reverb channel of your amp, you can The tone you seek can be obtained very easily by simply replacing a short wire with a capacitor and changing the value of a capacitor on the component board. If you want to know more about this method, read on for more details.

Rocky Mountain Summer Conservatory
(402) 884-5659
Omaha NE
Omaha, NE

Data Provided by:
Chadron State College
(800) 242-3766
Chadron NE
Chadron, NE

Data Provided by:
University of Nebraska - Lincoln
(800) 742-8800
Lincoln NE
Lincoln, NE

Data Provided by:
University of Nebraska - Kearney (UNK'S MUSIC PROGRAM)
(308) 865-8441
905 West 25th Street
Kearney, NE
 
Nebraska Wesleyan University (NWU Department of Music)
(402) 465-2218
5000 Saint Paul Avenue
Lincoln, NE
 
Schoolhouse Fiddlecamps For Intermediate/Advanced Fiddlers
(402) 275-3221
Avoca NE
Avoca, NE

Data Provided by:
Schoolhouse Fiddle Camps For Beginners
(402) 275-3221
Avoca NE
Avoca, NE

Data Provided by:
University of Nebraska - Omaha (UNOmaha Department of Music)
(402) 554-3446
6001 Dodge Street
Omaha, NE
 
University of Nebraska - Lincoln (UNL, School of Music)
(402) 472-2503
108 Westbrook
Lincoln, NE
 
Dana College (Music Department)
(402) 426-7222
2848 College Drive
Blair, NE
 
Data Provided by:

The Jangle-izer

IS THERE A WAY TO GET MORE JANGLE FROM THE NORMAL channel of my FenderPro Reverb amp? I have a 12-string Rickenbacker and would like to get that clean, jangly Vox tone, but without altering the reverb channel of my amp. —Anonymous

The tone you seek can be obtained very easily by simply replacing a short wire with a capacitor and changing the value of a capacitor on the component board. This modification will work with almost any two channel Fender amp (Twin, Super, Pro, Bandmaster, Showman, etc), and it is easily reversible should you want the stock wiring again.

This mod requires only two parts: a .01uf/400-volt capacitor and a 5uf/25-volt electrolytic capacitor. You’ll need a soldering iron and solder too, of course.

Unplug the amp and put the standby switch in the “play” mode to drain any stored electricity from the amp. Remove the four chassis screws on the top of the amp; remove the upper back panel and the cabinet strain relief on the AC cord. Unplug the speaker and remove the chassis from the cabinet. With the back of the amp facing you and looking into the chassis at the right side, you should be able to match up the components in the amp with the layout in Diagram 1. Make sure your amp is similar to the drawing before proceeding.

Notice there is a straight wire connecting the middle of the volume pot to the bright switch. You are going to replace this wire with the .01uf capacitor. Next, locate the 25uf capacitor that is going to pin 3 of the first preamp tube. You are going to replace this capacitor with the 5uf capacitor. Pay attention to the polarity of this cap. The plus (+) lead should face pin 3 of the first preamp tube, and the minus (–) lead should face the front of the amp. Double-check your work, by comparing it to Diagram 2. This is what the amp should look like now.

Put the old capacitor and the removed wire in a baggie and stash it in the bottom of the amp in case you want to put it back to stock wiring later. Reinstall the chassis, the AC cable strain relief, and the upper back panel. Plug in the speaker and you are ready to test it (make sure the speaker is plugged into the main speaker jack and not the external speaker jack). Turn on the amp, plug in your 12-string Rickenbacker, and get your Byrds on! —Gerald Weber, Kendrick Amplifiers

Click here to read the rest of the article from Guitar Player


Guitar Player is a trademark of New Bay Media, LLC. All material published on www.guitarplayer.com is copyrighted @2009 by New Bay Media, LLC. All rights reserved